Koch-Chemie Ceramic Allround C0.02 — Universal Ceramic Coating, 75 ml

Ceramic coating with a high hydrophobic effect

Ceramic Allround C0.02 is a ceramic coating that can be used on a variety of surfaces to provide long-lasting protection. Under the influence of air humidity after applying the composition to the surface, a chemical reaction begins. As a result of the chemical reaction, a strong mechanical bond is formed between the surface and the composition. The composition is applied in a very thin layer. Complete hardening of the coating occurs in approximately nine days. Ceramic Allround C0.02 creates a durable hydrophobic layer with very good water repellency. The coating has characteristics that facilitate easy cleaning of the surface, making cleaning the treated surface easier. The best option is gentle, hand washing. The achieved gloss of the coating is maintained even after using acidic and alkaline shampoos. The hardened ceramic coating protects the paintwork from environmental influences such as UV rays, road salt, bird droppings and rust deposits, and reduces mechanical damage. All of the above significantly contributes to maintaining the status of the vehicle and its attractiveness, which increases its value.

Properties of ceramics Allround C0.02

• Long-term surface protection with a service life of 18-24 months.

• Smooth hydrophobic surface with lotus effect

• Stable shine even after using acidic and alkaline cleaning agents

• Resistant to chemicals, road salts, alcohol in washer fluid, bird droppings, rust and UV radiation.

• Protection of varnish from corrosive and acidic products in the range from 5 pH to 12 pH, exception: KCU protector, KCU NANO and KCU Euro wash. Drying agents and preservatives of all categories.

Recommendations for use

Before starting work, thoroughly clean the vehicle with alkaline shampoo. Please do not use preservative shampoos. In case of heavy soiling, such as tree sap, rust, bitumen, etc., additionally treat the body with cleaning clay (red or blue), TEA resin remover, or similar appropriate care products. Preparation of heavily or moderately damaged paintwork is carried out mechanically, or using an abrasive polish - coarse-grained Heavy Cut H9.02 or fine-grained Fine Cut F6.01, depending on the condition. For correct use of the product, please read the instructions for use of Heavy Cut H9.02 and Fine Cut F6.01. Processing slightly damaged paintwork and removing holograms after polishing with Heavy Cut H9.02 or Fine Cut F6.01 is done using Micro Cut M3.02 - a micro-abrasive polish to give a mirror shine. In this case, an eccentric grinder with a forced action drive is used. Please read the instructions for use of Micro Cut M3.02. Completely remove any remaining polish using a microfiber cloth. Take a microfiber cloth soaked in silicone and wax remover (art. 207005) in one hand and wipe all surfaces without pressing. Immediately before they dry, go over the treated surface with your second hand using a new microfiber cloth. This is the only way to completely remove any remaining surfactants, drying agents and oils contained in polishes from the surface and prepare it for good adhesion when using Ceramic Allround C0.02. Attention: for sensitive universal or single-layer paintwork, the silicone and wax remover should be diluted with water in a ratio of 1:4. It is preferable to use distilled water to avoid possible clouding of the surface. Buff the remaining strips without pressure with a clean microfiber cloth. As a result, in sunlight or the light of a test lamp, no scratches or holograms should be visible on the surface. After this stage, it is not allowed to touch the paintwork with your palms or fingers due to the risk of damaging adhesion; use gloves. The surface is thus ideally prepared for the application of Ceramic Allround C0.02. To apply the composition, use a special microfiber Application towel wrapped around the applicator. Apply Ceramic Allround C0.02 to the surface of the microfiber Application towel and quickly spread it in a cross motion over the paintwork. An even film of liquid should be visible on the surface. After two cross movements (two horizontal and two vertical), allow the product to dry for approx. 6-8 minutes and then polish it with the included microfiber Coating towel. To do this, first remove excess compound from the surface, and then polish the applied compound without pressure with the clean side of the napkin in a circular motion from the outside inwards. Check with a test lamp that the varnish is not dull/foggy. Consumption for a passenger car is approximately 15-20 ml. Important information about

Application

Use the product on the intended vehicle surface for the task described above. Follow the product label and safety documentation for the exact application method, working time and dilution.